Change Watch Battery Now I Cant Get Back on Again

Download Article

Download Commodity

Depending on the lookout, changing the battery to become information technology ticking once more is often a unproblematic task that yous can do at dwelling house with a few tools and the proper techniques. Going to a spotter repair shop and having a specialist alter the bombardment is expensive and time-consuming, but you almost likely can do it yourself. The method for changing the battery volition change based on the brand, blazon, and style of your item scout. By taking the proper precautions and carefully following the correct methods, y'all can rapidly and hands replace a faulty or dead bombardment in your favorite sentry.

1. ane

   Discover the minor indentation on the back of the picket. Turn the watch over and find the small pigsty or indentation that's on the side of the watch, betwixt the watch back and the watch itself. This indentation is created specifically to assistance you pry off the back of the spotter.

   • If you can't find the indentation, scan the backside of your watch with a magnifying glass.
   • Wear a pair of dust free latex gloves when replacing your battery.

2. 2

   Slip a sharp tool into the indentation. Find a tool that's small enough to fit into the indentation yous discovered. Tools like a small flathead screwdriver created for eyeglasses or a modest blade may fit it into the indentation.^[1]

   Advertisement

3. 3

   Twist the tool to pop off the back casing. Utilize the blade or the screwdriver like a lever to pry upwards ane side of the lookout back. Once it comes loose, you can catch onto it with your manus to carefully remove the back of the watch.^[two]

4. 4

   Snap the back of the scout back into the casing. Afterwards you replace the battery, marshal the dials on the side of the watch with the indentations on the back of the watch. Press down heavily on the sentinel back until it snaps back into place.^[3]

   • Information technology's important to line up the back of the watch perfectly or you run the risk of damaging the watch's internal parts.
   • Some watches require a lookout man press to reattach the back to the watch.

   Advertisement

1. i

   Unscrew the screws from the back. There should be small-scale screws on the backside of your picket. These screws proceed the back in identify. To remove them, use a small-scale screwdriver that you would utilise for eyeglasses and plough the screws until you tin can remove them from the watch.^[4]

   • Brand sure to put the pocket-size screws in a safe place, like a ziplock bag, and so that you don't lose them.

2. ii

   Remove the back plate. Once you remove all of the screws from the back of the spotter, the back should easily lift up. This volition expose the watch battery and other internal parts in the sentinel.^[five]

3. 3

   Rescrew the screws into the dorsum of the lookout. Once you replace the bombardment, printing the back of the watch back onto the spotter and take the small screws that you removed earlier and screw them back into their holes.^[6]

   Advert

1. one

   Locate the indentations on the back of the watch. In that location should exist slots on the dorsum of the spotter that are big enough to fit the edge of a money. These are created intentionally for easy opening of the watch back.^[7]

2. ii

   Insert a quarter into one of the slots. Identify the border of the quarter into the indentation on the back of the watch. If information technology doesn't fit, employ a smaller money like a penny or dime.^[8]

3. 3

   Rotate the coin counter clockwise. As you rotate the coin, the small screw on the dorsum of the watch should come and the dorsum should undo from the picket.^[9]

4. 4

   Remove the watch dorsum. Apply your hands to advisedly lift up the backside of the watch. Brand certain that you rotated the coin slots a total turn or the back won't come up loose.^[x]

   Advertizing

1. 1

   Go a brawl of thumb tack or glue tack. You lot'll need to go a ball of a viscid thumb tack or glue that will adhere to the back of the lookout man and help you rotate it. You can purchase this at most arts and crafts stores or online.^[11]

   • There are besides grip-balls that are made specifically to open the back of a screw off sentry.

2. 2

   Press the tack confronting the back of the sentry. Knead the tack until information technology'southward soft and viscous. Printing it difficult against the dorsum of the picket.^[12]

3. 3

   Twist the tack counter clockwise and twist off the back. Once the tack is attached to the back, twisting information technology counterclockwise should loosen the back of the sentinel until information technology's not attached.^[13]

   Advertizing

1. ane

   Undo the strap and turn the watch over. It's easier to work with the watch if you're unobstructed. Undo the strap or remove the ring completely and turn the lookout over.^[xiv]

2. ii

   Remove the back of the watch. 4 types of scout backs include snap offs, screw-off backs, swatches, and backs with screws property them together. Examine the back of your watch to decide what kind of watch you accept.^[fifteen]

   • Screw off backs will have notches around the edges on the back of the watch.
   • Snap offs volition have a completely smooth back with a modest cut or indentation where the back of the watch meet and picket come across.
   • Swatches will have a slot on the dorsum where you tin can fit a coin.

3. three

   Remove any clip that may exist property the battery in place. In one case you remove the back, you'll be able to run into the internal components of the scout. Often, there will be a something blocking the battery from slipping out. This could exist a clip, retaining bar, and plastic cover.^[xvi] Wait at the bottom of the clip to discover the pocket-size hole near the lesser of the clip. Insert a small screwdriver into the hole and press up with your screwdriver to disengage the prune. This should make your battery accessible.^[17]

   • Wear a pair of dust gratis latex gloves when replacing your battery.
   • Some watches won't take anything roofing upwardly the battery. In this case, you can skip this stride.

4. iv

   Take find of the position of the battery. Before removing the battery, take note of its position and which side is facing upward. Have a wait at the writing on the battery so that you know which kind y'all should go to replace it. The battery will be circular disc that'southward around three/viii of an inch (nine.v mm).^[18]

5. five

   Ease the bombardment from the casing. Using plastic tweezers, position one side of the tweezers under the bombardment. Pry up with the tweezers to remove the battery from its casing.

6. 6

   Push button the new battery into place. Take your replacement battery and stick it in the spot where your quondam bombardment was. Utilize the plastic tweezers to press it back into identify. Avert hit or disrupting the other internal parts of the picket.^[19]

7. seven

   Check that the lookout man works earlier reattaching the back. If the sentinel is not working, you may have put the bombardment in astern, or information technology could be damaged. Double check that the bombardment is incorrectly installed. If information technology yet doesn't work, consider taking information technology to a professional for repair.^[20]

   Advertisement

Add New Question

• Question

  Practise I need a special tool to remove the back of my watch?

  

  Normally, a very fine tip flat head screwdriver is what y'all demand. You can get a set of fine Philips and flat drivers in what is often referred to as a "jeweler'due south" screwdriver set, usually for under $5.00 (Usa).

• Question

  I take a timex that I replaced the battery in, however, now I tin can't get the back slice to snap back on.

  

  Make sure that y'all're properly lining up the dials on the spotter earlier applying a lot of pressure with your fingers onto the dorsum of the watch. You might need a special tool to utilise more pressure if it's not properly snapping back on.

• Question

  I bought a new battery but it doesn't sit snug in the example. It worked when I held it down but when I put the cover on, it didn't work. Why would it be a wobbly fit?

  

  The battery could be not right one, or the battery holder is broken. Get to a watchmaker for further help.

• Question

  What exercise I do if it doesn't have a removable back-stop?

  

  It has to be removable. If information technology has screws, unscrew it. If information technology doesn't have screws, look on the side of the cover for a flap or a part that'due south similar a flap, or an open space. Utilize a knife or something to pry it open. If you can't pry it open up, then go to a watchmaker to open information technology. Now the pry open up kind of watches are hard to put dorsum, and then be super careful.

• Question

  What can I do if I tin can't get the screws on the dorsum of my watch out?

  

  Go to a scout store, and ask them to try to get it out for you. Information technology might take rusted close, and then information technology might not piece of work.

• Question

  Can I utilise AAA bombardment number 2025 to replace a battery number 934?

  

  No. This battery is used to replace 280-205, 5003LC, BR2025, DL2025, ECR2025, and SB-T14 batteries.

• Question

  How and where do I get a proper battery if the old one was missing?

  

  If you have a jewelry shop most y'all, go there and ask for a scout battery. Be sure to tell them what the brand is and then they know what to become for your sentry.

• Question

  Tin a person'south body pull out the accuse from a watch battery?

  

  Your watch can be afflicted by static electricity or electrical equipment, just non your body.

• Question

  Will this work on a Timex sport watch?

  

  Yes.

• Question

  What size spiral is usually used to hold prune on battery? I lost i while trying to replace battery and would like to buy the screw

  

  Watch screws are anywhere between .30mm and ane.20mm. Take your watch to a professional person so they can exam different screws and decide what 1 you need.

Testify more answers

Enquire a Question

200 characters left

Include your electronic mail accost to become a message when this question is answered.

Submit

Ad

Things You'll Need

• Plastic tweezers
• Jeweler's screwdriver
• Dust free latex gloves
• Magnifying drinking glass (optional)
• Replacement battery

Thanks for submitting a tip for review!

• If you accept an expensive watch, consider taking it to a professional instead of replacing the battery yourself.

Ad

Virtually This Article

Article Summary X

To modify a watch battery, figure out if the watch back snaps off or if it's held in place by screws, then remove it accordingly. If there's a clip holding the bombardment in identify, insert a small screwdriver into the hole and press upwards to disengage it. Then, pry the one-time battery out of the casing with plastic tweezers, discard information technology, and button the new battery into identify. Exist sure to cheque that the watch is working before reattaching the dorsum! For tips on removing unlike kinds of lookout man backs, read on!

Did this summary help yous?

Thanks to all authors for creating a page that has been read 1,264,235 times.

Did this article assist you?

mangoldpands1942.blogspot.com

Source: https://www.wikihow.com/Change-a-Watch-Battery

Share this post